Salmson SIL 405-27/3 -

IL 50/270-3/4

Item no. : 2088326-2120758

Your advantages

Reduced life cycle costs thanks to optimized efficiency
Standard condensate drainage holes in the motor housings
Can be used flexibly in air-conditioning and cooling systems, with application benefits due to direct draining of condensate via optimised lantern design (patented)
High standard of corrosion protection thanks to cataphoretic coating
High worldwide availability of standard motors (according to Wilo specifications) and standard mechanical seals

Construction
Glanded pump in in-line design with flange connection.

Application
Pumping of heating water (acc. to VDI 2035), cold water and water/glycol mixtures without abrasive substances in heating, cold water and cooling systems.

Scope of delivery

Pump
Installation and operating instructions

Technical data

Permissible temperature range -20 °C to +140 °C
Mains connection 3~400 V, 50 Hz (others on request)
Protection class IP 55
Nominal diameter DN 32 to DN 250
Max. operating pressure 16 bar (25 bar on request)

Materials

Pump housing and lantern: Standard: EN-GJL-250; optionally spheroidal cast iron EN-GJS-400-18-LT
Impeller: Standard: EN-GJL-200; special version: Bronze CuSn 10
Shaft: 1.4122
Mechanical seal: AQEGG; other mechanical seals on request

Description/construction
Single-stage, low-pressure centrifugal pump in in-line design with:

Mechanical seal
Flange connection with pressure measuring connection R 1/8
Lantern
Coupling
IEC standard motor

COUNTER FLANGE KIT DN50 PN10

Item no.: 2105581

Mating flanges:

Made of steel.
Counter flanges (weld) are delivered complete (in pairs) with bolt, nut and flange gasket.

Flange gasket DN 50 PN6/10

Item no.: 2150974

Flange gasket DN 50 PN6 / 10, Klingersil:

Thickness: 2 mm.
Inner diameter: 61 mm.
Outer diameter: 96 mm.

SWITCH BOX SK602N

Item no.: 2120444

Wall-mounted unit for electrical connection of single-phase and three-phase pumps with integrated thermal winding contacts (WSK) for monitoring the winding temperature (full motor protection).
Automatic reactivation of pump after power failure and automatic fault acknowledgement after cooling off of the motor.

Equipment/function:

Full motor protection tripping unit for pumps with thermal winding contact (WSK)
Switch on/off with integrated run signal light
Terminals for external, potential-free activation/deactivation
Connection terminal strip

SWITCH BOX SK622N

Item no.: 2120445

Wall-mounted unit for electrical connection of single-phase and three-phase pumps with integrated thermal winding contacts (WSK) for monitoring the winding temperature (full motor protection) and external run/fault signal.
Automatic reactivation of pump after power failure and automatic fault acknowledgement after cooling off of the motor.

Equipment/function:

Full motor protection tripping unit for pumps with thermal winding contact (WSK)
Switch on/off with integrated run signal light
Fault signal light
Terminals for external, potential-free activation/deactivation
Potential-free contacts for external run signal (SBM) and fault signal (SSM)
Connection terminal strip

Scope of delivery:

Switchgear SK 622N
4 threaded cable connections M20
Installation and operating instructions

Difference pressure sensor 10 m

Item no.: 2136454

The differential pressure sensor kit enables dp-c and dp-v control of the frequency-controlled high-pressure centrifugal pumps.
The sensor measures the differential pressure between the suction ports and discharge ports to the pipes, and converts this into an electrical signal 4-20 mA, which is used by the frequency converter to regulate the pressure of the pump. The value of the output current is proportional to the differential pressure.

Difference pressure sensor 20 m

Item no.: 2136456